CRT(Cathode Ray Tube)

-
Important:
  • During discharge the positive is a cathode, the negative is an anode.

  • During charge the positive is a anode, the negative is a cathode.


 

What is CRT?

=> CRT is a device which converts electrical signal into visual signal.

• Now before anything else it's important to understand the working and it's diagram properly.


• let's see work of each component in this diagram

1) Cathode: Cathode emits electron when it gets heat up by heater.

=> Cathode can be(Cobalt,Nickel,and manganese)

=> Anode made of(Zinc and lithium)

2) Grid Focuses and pass Electron beam at high speed.

3) Pre Accelerating Anode: It provides path to electrons

4) Vertical deflection plate: It deflects electrons beam up or down direction on screen as y-axis does

5) Horizontal deflection plate: It deflects electrons beam Right or left as X-axis does.

6) Aquadag coating: If electrons comes out of their path then it repels and helps electrons to come again in focusing path

7) Screen is coated with phosphore.

 • please refer above point simultaneously as diagram.


• when electrons are passing



=> Gray color tube at the back is CRT tube.


=> This is Cathode of RGB color.

• If you want to see Animated working of CRT Link is below:

https://youtu.be/Gnl1vuwjHto


*You can leave a comment if you have doubt in it.



Comments

Post a Comment

Popular posts from this blog

Functions of graphics

-
Image
 • First will discuss basic geometric shapes and base on that we will make a simple program where we will have a x and y axis and all the shapes in it. 1) Line Function => line function is used to draw a line by just giving 4 points. syntax:       void line(int x1, int y1, int x2, int y2); Where:          x1 : initial x-coordinate        y1 : intial  y-coordinate        x2 : end x-coordinate        y2 : end y-coordinate Example    : line(100, 100, 200, 200); Explanation : A line would be drawn from point(100, 100) to point(200,200). 2) Rectangle Function => Rectangle function is used to draw a rectangle.  => Rectangle function is same as bar function already discussed in last post, only difference is in bar function we get only 3 lines in output, but in rectangle we get all the four lines. =>Coordinates of left top and right bottom corner are required to draw the rectangle. left specifies the X-coordinate of top left corner, top specifies the Y-coordinate of top left corne
Read more

Line Basic Concepts

-
Image
 • We are going to study about Line Basic Concepts on Raster Screen. • so we are going to discuss what are the different ways in which line can be represented on Raster Screen and some of there respective features. 1) Vertical and Horizontal Line  • They have same width. • Straight line.  • Effective spacing is less. • More brighter. 2) 45° Line  • Width is not a constraint.  • Straight line. • More effective spacing. • Less brighter. Explanation:  • Point to remember is when there is more spacing between the points of line less brighter it will be and vice versa.  • But more spacing leads to effectiness in orientation of line. 3) Line with other orientation • In both of the above image the lines are nethier straight nor of same width. • Here points of line that is Pixel is approximated because while drawing the single line at point we get two points one is above the line and another is below the line. • But here approximation doesn't make a wide difference because pixel are very c
Read more

Shadow Mask technique

-
Image
  1) Shadow Mask technique is used in Raster Scan Display and produces wide range of colour, which wasn't possible in Beam penetration technique. 2) Here on the screen we have 3 dots of each color which means one pixel has three value of color i.e RGB which can create many different shades of color. 3) So in this technique we have 3 electron gun's which are assigned for there respective color RGB and one more most important thing that is a grid just behind the screen which is known as "Shadow Mask Grid" . 4)  Shadow mask grid is pierced with small round holes in a triangular pattern. 5) Th e 3 electron beams are deflected and focused as a group onto the shadow mask, which contains a sequence of holes aligned with the phosphor- dot patterns . 6) There is one gun for each of 3 Color RGB . 7) when these three colors mixed together can create all the colors we see on the screen, but remember these gun don't shoot the bullets instead they shoot a powerful beam of elect
Read more